A Hammond garage works hard. Tires roll in hot from the road. Oil drips in the same parking spot. The door stays up, and the sun hits the slab.
Bare concrete shows that life fast. It dusts under your shoes. It holds stains in its pores. A mop never quite gets the gray clean.
Polyaspartic flake coatings put a tough colored skin on that slab. We broadcast flakes into a wet base coat. A clear polyaspartic coat locks the flakes in place.
Polyaspartic is a fast-curing kind of polyurea. Made the right way, it stays stable in sunlight. It has a low tendency to turn yellow. That matters when the door faces the afternoon sun.
Homeowners call us when the old floor looks tired. Some have peeling paint. Some have a plain slab that stains every month. A flake floor is the fix we use for those garages.

What this garage floor does
A polyaspartic flake coating does three jobs. The base coat bonds to a sound slab. The flakes set the color and hide small pits. The clear coat takes the sun, the tires, and the spills.
Hammond homeowners pick this floor for three reasons. Each one shows up in a normal bay with the door open.
- The clear coat is made to stay clear in sunlight.
- The flakes add color and a light texture underfoot.
- The resin cures fast, so the garage is not down for a long week.
The flakes are vinyl chips, not paint speckles. A full broadcast covers the base so the color looks even. The clear coat is what your tires touch. We coat garages in Hammond, Covington, Mandeville, Ponchatoula, and Madisonville.
See our flake coating options in Hammond. Tell us about the garage and we will look at the slab.
A bare slab stains, dusts, and stays rough
Concrete is full of tiny pores. Oil, road salt, and leaf stains sit in those pores. You can sweep every week. The gray still looks blotchy.
Garage paint can look fine for a few weeks. Hot tires soften it and peel it. Water gets under the loose film. Then you are back to a stained slab.
A sound flake floor keeps spills on top. You still wipe them up the day they happen. No coating is a bin for old gasoline. Read how a coated garage floor handles oil and chemicals.
The clear coat holds its color in Hammond sun
The long record at the Hammond station puts the average July high near 92°F. An open garage door puts that heat on the floor. It also puts direct sun on the clear coat.

Standard epoxy can amber where the sun hits. The color shift shows up first by the door. A light floor shows it sooner than a dark one.
Polyaspartic coatings made with aliphatic isocyanates stay light stable. They have a low yellowing tendency in sunlight. In plain terms, the clear coat is built not to yellow.
The clear coat is the layer the sun hits. That is why we want polyaspartic on top of the flakes. Some systems still use epoxy under the flakes. Epoxy can be a strong base on a clean slab.
The top coat is the one that has to live in the light. Ask us which stack fits your garage. This resin sits in the polyurea family. See how a polyurea coating relates to this floor.
Flakes hide wear and add a light grip
A full flake broadcast covers the base color. Small pits and old stains hide under the blend. You pick the colors with us. We can lean gray, or we can pull a color from the house.

A full broadcast means the chips touch each other. You should not see much of the base color. A light sprinkle looks speckled and hides less. Garages that take oil and sun do better with a full broadcast.
The chips also break up a glossy shine. A wet shoe gets more bite than it does on smooth paint. A wet floor can still be slick. Tell us if the bay stays damp.
Light flakes show dirt faster than a mixed blend. A mid-tone blend hides dust between sweeps. See garage flake color choices before you pick a bag.
You get the garage back sooner
Polyaspartic is built for a fast cure. On many professional systems you can walk the floor the same day. A car often waits until the next day. Heat and humidity in our area can change that clock.
We give you the window before we start. That window comes from the product sheet and the weather. Park early and a hot tire can print the new coat.
Hot tires are the other daily test. A tire that has been on the road is warm. If the coat is still soft, that tire can leave a print. Follow the park window and the print risk drops.
A slow epoxy system often needs several days before a car parks. With one bay, those days push the cars into the drive. Tools end up in the yard. Rain here does not wait on a cure chart.
What we check before we coat the slab
Every garage visit starts with the slab, not the color chart. We look for cracks, old paint, and deep oil spots. We look at where the sun lands when the door is up. We ask how many cars park there, and how soon you need them back.
A dry, sound slab can take a flake system. A wet slab, or a slab that is breaking up, cannot. Coating those floors traps the problem under a pretty skin. We would rather delay the resin than peel it later.
A few limits before you book
Polyaspartic is a strong garage floor, and it has limits. The mixed resin sets fast, so a rushed DIY job shows lap lines. A box kit is also thinner than a pro system. Thin film wears through at the tire tracks.
We do not coat a dirty slab and hope. Old paint, sealer, and loose chips have to come off. Stable cracks get repaired before the base coat. A crack that is still moving needs a plan first.
You can put the system on concrete. You should not put it on wet, sealed, or crumbling concrete. We look at moisture, oil, and the joints on the visit. If the slab is the problem, we say so before we coat it.
A full broadcast feels textured under bare feet. Some people want a smoother look. We can talk through a lighter flake load. The trade is less hide over stains.
A normal install day follows five steps. We will adjust them if the slab needs repair first.
- Move the cars and clear the floor.
- Clean the slab and repair the stable cracks.
- Lay the base coat and throw the flakes until the base color is gone.
- Seal the flakes with the clear polyaspartic coat.
- Wait for the window we give you, then park.
If you are still comparing floors, start with what belongs on a garage floor. If paint is still on your list, read why garage paint fails on concrete.
| Garage paint | Basic epoxy | Polyaspartic flake | |
|---|---|---|---|
| Sun | Fades and peels | Can amber by the door | Clear coat is made to stay light stable |
| Park a car | Film fails in patches | Often several days | Often the next day, if the sheet says so |
| Look | One flat color | Color, or a light flake | Full flake color under a clear coat |
| Spills | Soak in when paint fails | A sound film beats bare concrete | A sound film beats bare concrete. Wipe spills. |
| Hammond fit | Poor with the door open | Fine in shade, or as a base | A fit for sun, tires, and a short shutdown |
Care is a broom and a damp mop
Sweep the grit before it works into the clear coat. Grit is what puts dull tracks in a shiny floor. Mop with a mild cleaner and water. Skip harsh solvents unless we have named a safe one.
Wipe fresh oil when you see it. A coating resists a spill better than open concrete. A spill left for months can still mark the surface. A mat at the door catches gravel from the drive.
If this is the floor you want, let us look at the slab. We will say if polyaspartic flakes are the right coat. We will also say if the concrete needs work first.
Bring a photo of the floor and of the open door if you can. That photo shows us the sun and the stains. Then read our notes on planning a garage you actually use.



